Home decoration, many owners have questions, in the end is the first install the floor, or first install the door? Experts suggest this issue.
The reason why it is recommended to install the door first is as follows:
1. From the perspective of installation and coordination, after installing the door cover, the skirting line of the floor is installed and cut and fixed to cover the door. It will be more closely matched, and there is no need to pay for the closing of the skirting board. 2, from the point of finished product protection, said the first door, finished product protection is relatively easy, whether it is dripping styrofoam, glass plastic pollution, the installation of power tools for the use of the door, packaging waste, sawdust, drilling nail chisel impact. . . Operate directly on the concrete floor without damaging the floor;
※It is necessary to pay special attention to the fact that if the installation is very compact, we hope to finish the installation of the floor immediately after the completion of the door. We must wait for the sealant to dry on the door or negotiate the time to finish the floor, finish the cleaning, and then apply the glue. Sealing door covers and kicks, buckles.
Some homeowners worry: If the door is first installed, the door will open when the door is opened. What can be done? There may be two reasons for this: â–² The first possible reason is the original ground flatness or The leveling of the ground level is not enough, and some constructions emphasize that the leveling of the ground should be done according to the construction of Shunping. This argument is wrong, because only when the furniture is placed on the level ground will it stick to the vertical wall; remind you again. Emphasis: The leveling test standard is to check whether the deviation value is qualified on the basis of the level;
Avoid this kind of situation: Floor level and flatness are checked before laying the floor, that is, the flatness of floor pavement is not more than 3mm on the basis of the level of horizontal deviation, and the stone highest point and cement floor (the floor) The difference between the paving base should be consistent with the optional floor thickness plus the thickness of the floor mat to avoid artificial obstacles (that is, the floor is higher than the passstone or lower than the passstone); in addition, the solid wood floor that needs the paving keel should be reserved Floor + Keel Thickness; Method to check the levelness of the ground: Check the entire floor and corners with a two-meter horizontal test gauge and feeler gauge.
â–² The second possible reason may be that door security is not vertical. When opening the door leaf, it may take a fan or smash the floor; avoid this way: 1. The door shall be vertical when installed, 2. The lower door and the floor The reserved dimensions between the (floor-installed base layer) conform to the following requirements: floor thickness + mat thickness + reserved gap 5-8mm, reserved net size (without floor buckle thickness) minimum not less than 5mm, this is National standard. 3, door cover installation clearance reserved floor installation should seek the views of the owners, with a cork wedge to reserve the floor plus mat thickness, to maintain the installation of the door to press the floor of the relationship. Of course, if there are special circumstances can be flexible arrangements such as: 1, due to a long custom wooden doors, the ground and the top surface of the wall construction has been met with paving flooring conditions, waiting for the floor finished as soon as possible to customize the furniture or retired the original housing needs 2. The wooden door or metal door needs to fix the rails on the floor; 3. The wooden door fixed fan or decorative fan needs to be fixed on the floor, and the paving order can be arranged according to actual needs)
※ [Seriously reminded - the necessary conditions for the installation of wooden doors and floors]: ※ The wooden door and the attached base must be substantially dry, and the basic layer moisture content should not exceed 12%. The humidity is too high and it is easy to cause drums, cracks, deformations, etc.; Walls and new floors shall be leveled. Wall openings shall be solid, square, vertical, and dry. The ground shall be level, dry, free from sand, hollowing and cracking shall be controlled within the scope of quality requirements, and the flatness shall comply with the paving requirements; Of course, if you first install the floor and install the door , you will have the following problems: 1. The door is heavy, and it may cause damage to the floor. Workers walking around may scratch the floor. 2. There is a certain amount of wood dust and glue when installing the door, which will stain the floor. 3. Did not install the door, the floor kick line is not good to close.
However, this is not a big problem. The solution is as follows: 1. Before the door is installed, it is possible to protect the floor covering next to the door with a carton board and other materials. 2. Workers can be required to cut materials into the corridors or balconies where they are well-cleaned to avoid large dust. 3. The skirting board can be installed without first installing the door and then loading it; or leaving a length of the baseboard of the door closer to the door frame for a certain length. Do not nail it to death. The situation saw the skirting board and installed it.
The reason why it is recommended to install the door first is as follows:
1. From the perspective of installation and coordination, after installing the door cover, the skirting line of the floor is installed and cut and fixed to cover the door. It will be more closely matched, and there is no need to pay for the closing of the skirting board. 2, from the point of finished product protection, said the first door, finished product protection is relatively easy, whether it is dripping styrofoam, glass plastic pollution, the installation of power tools for the use of the door, packaging waste, sawdust, drilling nail chisel impact. . . Operate directly on the concrete floor without damaging the floor;
※It is necessary to pay special attention to the fact that if the installation is very compact, we hope to finish the installation of the floor immediately after the completion of the door. We must wait for the sealant to dry on the door or negotiate the time to finish the floor, finish the cleaning, and then apply the glue. Sealing door covers and kicks, buckles. Some homeowners worry: If the door is first installed, the door will open when the door is opened. What can be done? There may be two reasons for this: ▲ The first possible reason is the original ground flatness or The leveling of the ground level is not enough, and some constructions emphasize that the leveling of the ground should be done according to the construction of Shunping. This argument is wrong, because only when the furniture is placed on the level ground will it stick to the vertical wall; remind you again. Emphasis: The leveling test standard is to check whether the deviation value is qualified on the basis of the level;
Avoid this kind of situation: Floor level and flatness are checked before laying the floor, that is, the flatness of floor pavement is not more than 3mm on the basis of the level of horizontal deviation, and the stone highest point and cement floor (the floor) The difference between the paving base should be consistent with the optional floor thickness plus the thickness of the floor mat to avoid artificial obstacles (that is, the floor is higher than the passstone or lower than the passstone); in addition, the solid wood floor that needs the paving keel should be reserved Floor + Keel Thickness; Method to check the levelness of the ground: Check the entire floor and corners with a two-meter horizontal test gauge and feeler gauge.
▲ The second possible reason may be that door security is not vertical. When opening the door leaf, it may take a fan or smash the floor; avoid this way: 1. The door shall be vertical when installed, 2. The lower door and the floor The reserved dimensions between the (floor-installed base layer) conform to the following requirements: floor thickness + mat thickness + reserved gap 5-8mm, reserved net size (without floor buckle thickness) minimum not less than 5mm, this is National standard. 3, door cover installation clearance reserved floor installation should seek the views of the owners, with a cork wedge to reserve the floor plus mat thickness, to maintain the installation of the door to press the floor of the relationship. Of course, if there are special circumstances can be flexible arrangements such as: 1, due to a long custom wooden doors, the ground and the top surface of the wall construction has been met with paving flooring conditions, waiting for the floor finished as soon as possible to customize the furniture or retired the original housing needs 2. The wooden door or metal door needs to fix the rails on the floor; 3. The wooden door fixed fan or decorative fan needs to be fixed on the floor, and the paving order can be arranged according to actual needs) ※ [Seriously reminded - the necessary conditions for the installation of wooden doors and floors]: ※ The wooden door and the attached base must be substantially dry, and the basic layer moisture content should not exceed 12%. The humidity is too high and it is easy to cause drums, cracks, deformations, etc.; Walls and new floors shall be leveled. Wall openings shall be solid, square, vertical, and dry. The ground shall be level, dry, free from sand, hollowing and cracking shall be controlled within the scope of quality requirements, and the flatness shall comply with the paving requirements; Of course, if you first install the floor and install the door , you will have the following problems: 1. The door is heavy, and it may cause damage to the floor. Workers walking around may scratch the floor. 2. There is a certain amount of wood dust and glue when installing the door, which will stain the floor. 3. Did not install the door, the floor kick line is not good to close. However, this is not a big problem. The solution is as follows: 1. Before the door is installed, it is possible to protect the floor covering next to the door with a carton board and other materials. 2. Workers can be required to cut materials into the corridors or balconies where they are well-cleaned to avoid large dust. 3. The skirting board can be installed without first installing the door and then loading it; or leaving a length of the baseboard of the door closer to the door frame for a certain length. Do not nail it to death. The situation saw the skirting board and installed it. Decoration process
OTIS Elevator Steel Wire Rope, Thyssen Elevator Steel Wire Rope, KONE Elevator Steel Wire Rope, GiantKONE Elevator Steel Wire Rope, ThyssenKrupp Elevator Steel Wire Rope, Schindler Elevator Steel Wire Rope, XJ Schindler Elevator Steel Wire Rope, Xizi OTIS Elevator Steel Wire Rope, Mitsubishi Elevator Steel Wire Rope, Shanghai Mitsubishi Elevator Steel Wire Rope, Fujitec Elevator Steel Wire Rope, Hitachi Elevator Steel Wire Rope, Toshiba Elevator Steel Wire Rope, Hyundai Elevator Steel Wire Rope, LG Elevator Steel Wire Rope, Sigma Elevator Steel Wire Rope, Express Elevator Steel Wire Rope, GUANGRI Elevator Steel Wire Rope, FUJI Elevator Steel Wire Rope, BLT Elevator Steel Wire Rope, CANNY Elevator Steel Wire Rope, SJEC Elevator Steel Wire Rope, KOYO Elevator Steel Wire Rope, IFE Elevator Steel Wire Rope
Elevator Steel Wire Rope,Galvanized Elevator Steel Wire Rope,Lift Steel Wire Rope,Elevator Stainless Steel Wire Rope, Elevator Wire Rope, Elevator Rope
CEP Elevator Products ( China ) Co., Ltd. , https://www.zjfullelevatorreplacement.com