1. Infrared lamp operating conditions In general, the infrared lamp radiation power is proportional to the forward operating current, but near the maximum rated current of the forward current, the temperature of the device rises due to the heat dissipation of the current, making the optical emission power. decline. Infrared diode current is too small, it will affect the radiated power to play, but the operating current is too large will affect its life, and even make the infrared diode burned.
When the voltage crosses the positive threshold voltage (about 0.8V or so), the current begins to flow, and it is a very steep curve, indicating that its operating current requirements are very sensitive. Therefore, it is required that the operating current is accurate and stable, otherwise it will affect the performance and reliability of the radiation power. The increase in radiated power with the ambient temperature (increased ambient temperature due to its own heat generation) will reduce its radiated power. Infrared lamps are particularly long-range infrared lamps. Heat consumption is a problem that should be considered when designing and selecting.
Therefore, the use of infrared lamps must have a good constant current power supply and a good heat dissipation design. Midway Communications' zoom MCD, MDD, MED, and MBB series cameras have installed high-power infrared lamps (up to 24) and are powered by a high-power constant-current power supply. The internal circulation heat dissipation design enables them to reach remote nights. According to the effect (up to 220 meters) and the long life of infrared lamps.
2, infrared light utilization and red storm problems What is a red storm? Redstorm is due to the fact that the emitted infrared light contains visible light components.
Infrared lamps can be completely red-free (using 940-950nm wavelength infrared tube) or only a weak red storm. Middle Road Communications adopts AUCSITER infrared technology to reduce the infrared lamp's own heat consumption and to adjust the angle of infrared light to ensure that the infrared lamp's effective utilization rate reaches 90%. In the selection of infrared lamps, infrared light with a relatively large wavelength (910 nm) was selected, and red storms were strictly reduced to achieve a reddish effect.
3. Fogging and Frosting of Infrared Cameras The formation of fog and frost is caused by the condensation of saturated steam in the air, and is condensed into frost and fog due to the strong and weak cold environment. In the work process of infrared cameras, especially outdoor cameras often cause fog or frost on the protective window glass due to seasonal changes, temperature difference between day and night, and rain and snow conditions. As a result, cameras cannot see objects and directly affect the monitoring results. Midway Communications adopted the advanced electronic defrosting circuit to effectively control the saturated water vapor concentration in the chamber and achieved automatic defogging and defrosting.
4. Infrared camera's window glass cleaning The camera works in rainy, snowy or dusty environments. The window glass of the protective cover is prone to dirt and causes the camera's vision to be blocked. The solution is usually to add a wiper to the hood, and to control the wiper to clean the glass; another option is to use an invisible wiper window glass. Compared with ordinary window glass, invisible wiper window glass has the function of repelling water, dust, and snow.
5, infrared camera constant temperature due to the configuration of a larger heat infrared light, infrared light in the start, the entire working period (in 12 hours) in the infrared camera will have heat concentration, that is, the front end of the cavity temperature is high , If you can not evenly heat will affect the normal operation of the camera and other components. Middle Road Communications Co., Ltd. has solved this problem by designing and using an automatic air-conditioning system with forced cooling and cooling.
Automatic cooling and air conditioning adopts Peltier effect principle, temperature measurement control circuit can be automatically adjusted, the temperature inside the protective cover is constant within the normal operating temperature range of the camera, the temperature inside the cover is set at +5°C below the heating, +40°C above cold. Experiments show that the infrared integrated camera can work normally in an outdoor natural environment of -40°C to +70°C (direct sunlight).
6. In addition to the constant temperature of the infrared camera, the other advantage of using the automatic air conditioning system is that the infrared camera can be made fully enclosed, leaving no cooling holes to prevent the entry of dust, moisture, and corrosive gas, enabling it to To adapt to the harsh environment of dust, such as large coal mines can also be used normally.
When the voltage crosses the positive threshold voltage (about 0.8V or so), the current begins to flow, and it is a very steep curve, indicating that its operating current requirements are very sensitive. Therefore, it is required that the operating current is accurate and stable, otherwise it will affect the performance and reliability of the radiation power. The increase in radiated power with the ambient temperature (increased ambient temperature due to its own heat generation) will reduce its radiated power. Infrared lamps are particularly long-range infrared lamps. Heat consumption is a problem that should be considered when designing and selecting.
Therefore, the use of infrared lamps must have a good constant current power supply and a good heat dissipation design. Midway Communications' zoom MCD, MDD, MED, and MBB series cameras have installed high-power infrared lamps (up to 24) and are powered by a high-power constant-current power supply. The internal circulation heat dissipation design enables them to reach remote nights. According to the effect (up to 220 meters) and the long life of infrared lamps.
2, infrared light utilization and red storm problems What is a red storm? Redstorm is due to the fact that the emitted infrared light contains visible light components.
Infrared lamps can be completely red-free (using 940-950nm wavelength infrared tube) or only a weak red storm. Middle Road Communications adopts AUCSITER infrared technology to reduce the infrared lamp's own heat consumption and to adjust the angle of infrared light to ensure that the infrared lamp's effective utilization rate reaches 90%. In the selection of infrared lamps, infrared light with a relatively large wavelength (910 nm) was selected, and red storms were strictly reduced to achieve a reddish effect.
3. Fogging and Frosting of Infrared Cameras The formation of fog and frost is caused by the condensation of saturated steam in the air, and is condensed into frost and fog due to the strong and weak cold environment. In the work process of infrared cameras, especially outdoor cameras often cause fog or frost on the protective window glass due to seasonal changes, temperature difference between day and night, and rain and snow conditions. As a result, cameras cannot see objects and directly affect the monitoring results. Midway Communications adopted the advanced electronic defrosting circuit to effectively control the saturated water vapor concentration in the chamber and achieved automatic defogging and defrosting.
4. Infrared camera's window glass cleaning The camera works in rainy, snowy or dusty environments. The window glass of the protective cover is prone to dirt and causes the camera's vision to be blocked. The solution is usually to add a wiper to the hood, and to control the wiper to clean the glass; another option is to use an invisible wiper window glass. Compared with ordinary window glass, invisible wiper window glass has the function of repelling water, dust, and snow.
5, infrared camera constant temperature due to the configuration of a larger heat infrared light, infrared light in the start, the entire working period (in 12 hours) in the infrared camera will have heat concentration, that is, the front end of the cavity temperature is high , If you can not evenly heat will affect the normal operation of the camera and other components. Middle Road Communications Co., Ltd. has solved this problem by designing and using an automatic air-conditioning system with forced cooling and cooling.
Automatic cooling and air conditioning adopts Peltier effect principle, temperature measurement control circuit can be automatically adjusted, the temperature inside the protective cover is constant within the normal operating temperature range of the camera, the temperature inside the cover is set at +5°C below the heating, +40°C above cold. Experiments show that the infrared integrated camera can work normally in an outdoor natural environment of -40°C to +70°C (direct sunlight).
6. In addition to the constant temperature of the infrared camera, the other advantage of using the automatic air conditioning system is that the infrared camera can be made fully enclosed, leaving no cooling holes to prevent the entry of dust, moisture, and corrosive gas, enabling it to To adapt to the harsh environment of dust, such as large coal mines can also be used normally.
Stainless Steel Baking Cooling Rack
Baking rack,baking cooling mesh,Baking cooling rack,Cooling Rack, steel wire cooling rack, etc.
Baking wire mesh is made of high quality 304 stainless steel, never rusting and durable. Cooling Wire mesh does not have any coating or chemical ingredients, making food safer.
Multi-functional Grill Cooking rack: the wire mesh is mainly used for outdoor cooking, it can also be used as a cooling and baking rack. Or you can develop other uses for it.Baking Rack,Cooling Rack,Kitchen Baking Rack,Stainless Steel Cooling Rack,Oven Baking Rack
Shenzhen Lanejoy Technology Co.,LTD , https://www.szstainlesssteelwiremesh.com