ã€China Aluminum Network】 Aã€When installing the template, first wear gloves. Before installing the template, you should consider that the template may be cut. When cutting, consider the overall appearance and symmetry of both sides as much as possible. In one of the four folds of the front panel, one or two of the folds (two folds at the corners) are cut with a utility knife to a distance of 2mm from the plane of the template. (The leveling will affect the flatness of the installation. (Note: Due to the consideration of the flatness of the wall, the surrounding template is required to be 1cm smaller than the actual size.) Cutting method: Fix the template, use a utility knife and a ruler to characterize it more than three times, and cut the edge to cut it with scissors. 90-degree angle incision, hand-folded 2-3 times.
Remove the upper protective film before installing the template. When installing the template, first cut the corresponding surface of the template in the keel, cut the surface of the die on the edge strip, and pull out the edge clip to clamp the template. At this point, the triangular hanger can be clamped with the steel pliers and the main keel. And so on to complete the installation of the template by the front row. (Control the gap between the templates)
B, when the middle part of the template is installed, the two corresponding surfaces of the template are respectively stuck in the keel to control the gap between the templates and keep the seam straight. Note: After completing the installation of each row of templates, the triangular hanger shall be clamped with the steel pliers and the main keel.
C. When installing to the second row of templates, refer to steps A and B. First, install the template next to the wall and install the second row later.
D. Check the installation.
E. Installation sequence of aluminum buckles (important)
The installation of the aluminum buckle plate ceiling is not complicated. Pay attention to the installation sequence of the bathroom heater, water heater, exhaust fan, hood, and lamp. Do not install the exhaust fan (Yuba) directly on the aluminum buckle plate with screws. Otherwise, after the installation of the aluminum buckle plate, the owner of the exhaust fan (Yuba) will find that there is a "click" sound, because after the aluminum buckle plate is lifted, the closed space at the top will form a resonant cavity regardless of the quiet effect of the exhaust fan (Yuba). How good will be expanded many times. The correct installation sequence is: first install the Yuba, exhaust fan, and then do aluminum buckle plate ceiling (Yuba, exhaust fan expansion bolts and iron can be directly hung on the top of the coagulation. Better not the steel wire, the plasticity of the steel wire is relatively poor).
If the exhaust fan exhaust hose is longer (more than 1 meter long), it is better for workers to fix it on the top. Otherwise, the exhaust pipe will vibrate when the exhaust fan is turned on, and the “click†sound will be loud. The fixing method is very simple. It only needs to use scotch tape to fix it. It can reduce a lot of noise.
The correct order for the installation of the kitchen gusset plate is to fix the hood and flues of the hood first, and to select the location where the range hood needs to be installed at the other end, and to buy the lamp used in the kitchen, and do not need to install. Then the aluminum buckle plate ceiling. When it is necessary to install large lamps and lanterns, it is better to use wooden keel to reinforce the lamps alone. Although the light steel keel is not easy to be deformed in the ceiling, the large lamps are heavy, and the keel will change for a long time when they are hung on the keel.
Low porosity clay bricks are made of ruby, mullite and combined clay as the main raw materials, molded under high pressure and sintered at high temperature. The product has excellent high temperature Physical properties and chemical corrosion resistance. Low porosity clay bricks have good stability, the degree of erosion does not occur sudden change, than ordinary clay bricks use cycle increased 2-3 times. Thermal conductivity, specific heat and solubility, respectively, than ordinary clay bricks 2 times higher than 10% and 40%, heat storage capacity than ordinary clay bricks higher than 50% -60%, can improve the thermal efficiency of the kiln.
Arc Type High Alumina Bricks,Rotary Kiln High Alumina Curved Brick,Kiln Arch Refractory Bricks
Huixian Xinwei Refractories Co. , https://www.xinweirefractory.com