Most of the stone decoration works have not yet been completed and accepted, and various stone lesions have taken place, and remedial measures have to be sought. In fact, these troubles can be completely avoided. No matter where the stone pollution and damage come from, the fundamental reason is that natural stone itself has cracks and pores that have adsorption and permeability. If you do not perform protective treatment, it will inevitably lead to processing and storage. During transportation, installation, construction, and use, various lesions and pollutions occurred, accelerating the weathering process. The best way to solve the problem is to carry out six-sided protection of the stone , then the stone six-sided protection of concrete how to operate it? Following Xiaobian look at it.
Stone six-sided protection concrete operation
Protecting the stone is an indispensable process in the installation process of the interior stone. The protection of the stone is directly related to the use effect and the service life of the stone. The six-sided protection of the stone is the six faces of the stone. In terms of type, the chemical protection agent is applied more to the profiled surface to achieve the purpose of waterproofing, oil repelling, and anti-fouling. The so-called hexahedron is also called full protection.
After the decoration of the stone, the pollution of the upper and lower left and right sides is required. The following is the penetration of the material in the cement mortar. There are water, oil, and the pollution of domestic sewage and industrial pollution on the surface; there are pollutions such as adjacent caulking glue and cement. Therefore, the comprehensive protection of stone is widely recognized in the decoration industry in recent years. The method of operation must be carried out before the decoration of the protective treatment, there is immersion, smearing. After drying for 24 hours, special effects tests are performed to determine whether the brand and type of protective agent used correspond. Some stones should be brushed several times to achieve the purpose of better protection, especially granite. Once it is not properly protected, water spots are very serious and most of them cannot be restored. Then it can be used in large-scale projects. It should be noted that the protective agent applied on the six surfaces should not be the same, and the interface with the adhesive should be coated with an interface agent and increased in roughness to facilitate bonding.
Approach
1. Before protective treatment, the stone must be completely clean and dry before it can be constructed.
2. Apply with a brush or roller. A sufficient amount of 100 cc or more must be applied per square meter.
3. In the area where there is a gap, the drug is injected into the gap with a syringe needle so as to achieve a protective effect of saturation.
4. When applied on the surface, apply two coats. Apply evenly when applied. After the first coat is applied, wait for more than 10 minutes to allow it to penetrate completely. When applying the second coat, the dosage may be slightly increased or decreased depending on the current situation. 30 minutes after brushing, the surface is wiped clean until it is clean (the burned stone does not need to be covered with protective agent).
5. When applying on the back, apply a layer of thick coating. Apply evenly to the entire surface for 10 minutes. After application, wait for more than 10 minutes to allow it to evaporate and dry, and check whether the surface is slightly sticky or not. Film isolation, 30 minutes after brushing, before the full installation of stone works.
Editor's summary: The relevant information on the six-face protection of the stone is introduced here for everyone. I hope this article will be helpful to everyone. If you still have something you don't understand, you can leave a message to Xiaobian at the bottom. We will answer your questions as soon as possible.
Terrace Decoration Marble Tiles Marble Marble Floor Tiles
Recessed LED Downlight with built-in Microwave Motion Sensor
| Model | AM-6.0GY |
| Luminous flux | 800~900lm |
| Luminous Efficacy | >80lm/W |
| Colour Rendering index | 80 |
| Beam Angle | 140° |
| Light Decay | <30% over 10,000 hours |
| Rated Lifespan | >30,000 hours |
| Power consumption | 10 watts |
| Input voltage / Frequency | 80-260vac 50-60HZ |
| Reflector / Diffuser | Frosted diffuser |
| Operating Environment | -20°c~+50°c |
| Dimensions | Φ193*77mm |
| Hole Cut Size | Φ160~Φ180mm |
| LED Source | 56pcs SMD2835 |
| Working mode | ON/OFF or Full/Dim |
| Sensor Range | 180*360 degree |
| Sensor Distance | 6-8m Radius |
| Delay Time |
18-25s |
Solar Power,Solar Portable Power Station,Solar Power Panels,Solar Portable Power Station Camping
JIANGMEN MOSCOT OPTOELECTRONIC TECHNOLOGY CO.,LTD. , https://www.jmsensorsled.com