1. Processing of aluminum alloy doors and windows
The surface of the processed material must not have oil spots, aluminum chips, burrs or other stains; do not stretch excessively when any strip is embedded. It should be ensured that the strip is about 10 mm longer than the insert groove; the strip should be wrapped around one week, and the joint should be docked at the corner of the frame and should not be cut into several breaks.
The joints, hardware and metal linings used in aluminum alloy doors and windows should be treated with surface anti-corrosion treatment except stainless steel.
The glass block should be made of hard rubber or plastic, and no reclaimed rubber, wood chips or other absorbent materials should be used.
The bead should be firm after assembly, and the gap between the butts should be no more than 1mm.
The amount of overlap between the glass and the window shall be calculated from the edge of the window frame and the fan. The amount of overlap on each side shall be not less than 8 mm (the double glass shall not expose the aluminum spacer), and the glass shall be provided with a glass spacer under the assembly.
2, aluminum alloy doors and windows installation
Before installation, the position of vertical, horizontal (elevation) and wall thickness must be determined. When the net port is installed, the reserved gap between the window frame and the opening of the hole is 5-8mm. When installing, ensure that the gap between the upper and lower sides is uniform. When the burr is installed, the thickness of the connecting piece shall not be less than 2mm.
The diagonal deviation of the installation window frame is ≤2.0mm; the vertical deviation of the front and side frames (including the splicing materials) is ≤2.0mm; the horizontal deviation of the window frame (including the splicing materials) is ≤1.5mm; the elevation error is ≤5.0mm .
Fixing method When installing the net port, use the expansion hose to directly fix the window frame to the wall; when fixing, the screw must be tightened with a screw. Do not directly knock it with a hammer. When the burrs are used, fix the window frame with the expansion hose through the connecting piece. On the wall. No matter what method is fixed, the fixing point shall not exceed 600mm, and the fixing member shall not be less than 50mm into the structural body.
After the door and window frame is installed, there should be no arching, drooping, warping or deformation, so as to avoid obstructing the function of the switch; before installing the glass, the mortar and debris in the tank should be removed to make the drainage hole clear; after the window sash is installed, the appearance quality The surface is clean, no large areas of pitting, scratches, bumps, rust, etc.; the surface of the sealant applied is smooth, flat and free of air bubbles.
The finished parts are completely installed and firm, and there should be no misplacement or less loading. The sealing strips should be even and firm after assembly. The joints at the corners of the frame should be tightly bonded and free from grooving. There should be no broken ends.
The application of three-color Lamp Beads is mainly divided into two parts: 1, indicator 2, three-color lamp beads for outdoor lighting, and full-color lamp beads. Many of the three-color full-color lamp beads used for indicator lights use 0603, 0805 full-color lamp beads, which are mainly used in toys and electrical products, such as 1615 full-color three-color lamp beads. Most of the electric The three-color lamp beads used on the toothbrush are of this model. Of course, there are some direct plug-in rgb lamp beads, such as 5mmrgb lamp beads and 8mmrgb, which are used for indication purposes, such as low-power direct plug-in or small patch tri-color lamp beads for toy cars and remote control aircraft. Another place where the three-color lamp beads are more widely used are outdoor lighting fixtures, such as landscape lights and stage lights. Many of them use full-color lamp beads to make colorful light effects. For these outdoor lighting LED applications, many engineers recommend choosing relatively high-power 3-color lamp beads when selecting models. Like 5050rgb full-color lamp beads, 3528rgb full-color lamp beads, 3030rgb full-color lamp beads, 3535rgb full-color lamp beads, and high-power imitation lumens, integrated tri-color lamp beads, will be selected.
In fact, the RGBWW five-color lamp beads are based on the original RGB three-color lamp beads, adding two colors of warm white light and positive white light. This four-color and five-color lamp beads are generally used in light bars and stage lamp beads to create a special phosgene atmosphere. The general three-color lamp beads are mainly used for indications, such as remote control toys, electric toothbrushes and other products. Therefore, knowing the knowledge of the three-color lamp beads for these applications, the selection is relatively simple.
High Power Lamp Beads 1W,In-Line Led Double Color,In Line Led Red,Red Green Lamp Bead
Dongguan XINYUDA Technology Co., Ltd. , https://www.gdxige.com