Rubber and plastic insulation insulation material installation technical methods and essentials rubber and plastic insulation materials have seven series of products 1 engineering use Class1 rubber and plastic insulation products 2 split air conditioning rubber and plastic pipe 3 composite veneer rubber and plastic insulation products 4 open / closed-hole rubber Plastic sound-absorbing board 5 color rubber and plastic products 6 paving with rubber and plastic materials 7 supporting auxiliary products rubber and plastic insulation insulation installation should pay attention to the following points;
All the slits and joints need rubber-plastic glue sealing.
All tees, elbows, valves, flanges and other accessories are required to reach the design thickness after installation.
Do not use too much force when bonding the glue. The interface between all materials should be bonded under slight extrusion.
When installing, first the small tube and the small tube, first elbow, three-way straight tube, and finally the valve and flange.
When installing the chilled water pipe and the refrigeration equipment, the gap between the two ends of the rubber-plastic pipe and the iron pipe shall be glued together, and the bonding width shall not be equal to the thickness of the rubber material.
The slit of the pipe should be installed in an inconspicuous place as far as possible, and the slits of the two pipes should be staggered from each other.
Do not install the machine while it is in use. Do not switch on within 36 hours of installation.
The large-diameter rubber-plastic tube has become elliptical due to the packaging relationship. Please plan the flat side when you plan to open it.
The correct use of glue:
1 Shake the container before use to make the glue even. Pour the large tank of glue into the small tank container and seal it when not in use.
2 Use a short, hard brush.
3 Apply a thin, uniform special glue to the bonding surfaces at both ends of the material.
4. The natural drying time of the special watering is 3-10 minutes, and the length of time depends on the grade of the glue, the temperature and humidity of the atmosphere. Exposed time is more than 20 minutes.
5. When using, wait for the watering to dry naturally. The correct method of measuring the dryness is “Finger Touch Methodâ€. Touch the rubberized surface with your fingers. If the fingers do not stick to the surface of the material, and the surface of the material does not feel good.
6. When bonding, just align the two surfaces of the interface for a while.
7 If the placement time is too long, so that the two joints are not sticky when pressed together, repeat steps 2-6.
8 Usually, two square meters of adhesive surface can be applied per kilogram of glue.
9 Usually, the special glue can't be used below 5 degrees Celsius. When working in the environment of 5-10 degrees Celsius, put the glue in the room at 20 degrees Celsius.
10 When there is pressure, please don't wait for the glue to dry. Use wet bonding method, first place the material at the installation place, apply glue at the interface of the material, adjust the position of the two materials correctly, and stick quickly. Connected firmly.
11 Check that the anti-corrosive paint of the glue and the protective pipe is firmly bonded.
All the slits and joints need rubber-plastic glue sealing.
All tees, elbows, valves, flanges and other accessories are required to reach the design thickness after installation.
Do not use too much force when bonding the glue. The interface between all materials should be bonded under slight extrusion.
When installing, first the small tube and the small tube, first elbow, three-way straight tube, and finally the valve and flange.
When installing the chilled water pipe and the refrigeration equipment, the gap between the two ends of the rubber-plastic pipe and the iron pipe shall be glued together, and the bonding width shall not be equal to the thickness of the rubber material.
The slit of the pipe should be installed in an inconspicuous place as far as possible, and the slits of the two pipes should be staggered from each other.
Do not install the machine while it is in use. Do not switch on within 36 hours of installation.
The large-diameter rubber-plastic tube has become elliptical due to the packaging relationship. Please plan the flat side when you plan to open it.
The correct use of glue:
1 Shake the container before use to make the glue even. Pour the large tank of glue into the small tank container and seal it when not in use.
2 Use a short, hard brush.
3 Apply a thin, uniform special glue to the bonding surfaces at both ends of the material.
4. The natural drying time of the special watering is 3-10 minutes, and the length of time depends on the grade of the glue, the temperature and humidity of the atmosphere. Exposed time is more than 20 minutes.
5. When using, wait for the watering to dry naturally. The correct method of measuring the dryness is “Finger Touch Methodâ€. Touch the rubberized surface with your fingers. If the fingers do not stick to the surface of the material, and the surface of the material does not feel good.
6. When bonding, just align the two surfaces of the interface for a while.
7 If the placement time is too long, so that the two joints are not sticky when pressed together, repeat steps 2-6.
8 Usually, two square meters of adhesive surface can be applied per kilogram of glue.
9 Usually, the special glue can't be used below 5 degrees Celsius. When working in the environment of 5-10 degrees Celsius, put the glue in the room at 20 degrees Celsius.
10 When there is pressure, please don't wait for the glue to dry. Use wet bonding method, first place the material at the installation place, apply glue at the interface of the material, adjust the position of the two materials correctly, and stick quickly. Connected firmly.
11 Check that the anti-corrosive paint of the glue and the protective pipe is firmly bonded.
Floor Drain Cover,6 Inches Floor Cover,Bathroom Floor Drain Cover,Anti-Odor Square Floor Drain Cover
Kaiping City Jinqiang Hardware Products Co.,Ltd , https://www.jqfloordrain.com