1, floor tiles can not be mixed
Wall tiles and floor tiles are very different from the choice of clay ingredients to the firing process. The water absorption rate of wall tiles is about 10%, which is several times higher than that of a floor tile with a water absorption rate of only 1%. The floor of the bathroom and kitchen should be laid with low water absorption floor tiles, because the ground will often use a lot of water to wash, so that tiles can not be affected by water vapor, do not absorb stains. Wall tiles are made of glazed ceramics and have a high moisture content. The back of the wall tiles is generally rough, which also helps the adhesive to attach the wall tiles to the wall. Tiles are not easily affixed on the walls. Wall tiles used on the ground will absorb too much water and become difficult to clean. It can be seen that walls and floor tiles cannot be mixed.
2, leveling before the tile shop
The foundation should be cleaned before tiling, for example, lime plaster, latex paint, wallpaper, etc. on the wall, or dirt on the ground, must be cleaned, otherwise the cement mortar and the grass-roots layer will not be firmly bonded; in addition, if the wall itself There are cracks, should be properly handled before the tiling, in order to avoid future basic structural cracks caused by cracking or loss of wall tiles; as well as for the flatness or verticality gap is too big for the floor, wall, but also with cement mortar Leveling processing.
3, laying out the order of bricks and tiles
Posted floor tiles should be posted from the inside, such as the ground slope or floor drain, should pay attention to the direction of the slope to find the drainage; wall tiles should be laid from the bottom, for the sake of beauty, the bottom of the brick should be posted. After pressing the tiles, press the floor tiles. When there are half bricks, you should try to place them below. In addition, a wall cannot be attached to the top at a time to prevent the tile from being heavy and causing it to fall.
4, wall tiles to be fully immersed
Wall tiles have a high moisture content and must be considered when pasting. The tiling tiles should be soaked in water for at least 10 minutes before they are fully wetted.
Otherwise, the moisture in the mortar is quickly absorbed by the dried tiles and condenses quickly, which affects the fastness of the bond.
Wall tiles and floor tiles are very different from the choice of clay ingredients to the firing process. The water absorption rate of wall tiles is about 10%, which is several times higher than that of a floor tile with a water absorption rate of only 1%. The floor of the bathroom and kitchen should be laid with low water absorption floor tiles, because the ground will often use a lot of water to wash, so that tiles can not be affected by water vapor, do not absorb stains. Wall tiles are made of glazed ceramics and have a high moisture content. The back of the wall tiles is generally rough, which also helps the adhesive to attach the wall tiles to the wall. Tiles are not easily affixed on the walls. Wall tiles used on the ground will absorb too much water and become difficult to clean. It can be seen that walls and floor tiles cannot be mixed.
2, leveling before the tile shop
The foundation should be cleaned before tiling, for example, lime plaster, latex paint, wallpaper, etc. on the wall, or dirt on the ground, must be cleaned, otherwise the cement mortar and the grass-roots layer will not be firmly bonded; in addition, if the wall itself There are cracks, should be properly handled before the tiling, in order to avoid future basic structural cracks caused by cracking or loss of wall tiles; as well as for the flatness or verticality gap is too big for the floor, wall, but also with cement mortar Leveling processing.
3, laying out the order of bricks and tiles
Posted floor tiles should be posted from the inside, such as the ground slope or floor drain, should pay attention to the direction of the slope to find the drainage; wall tiles should be laid from the bottom, for the sake of beauty, the bottom of the brick should be posted. After pressing the tiles, press the floor tiles. When there are half bricks, you should try to place them below. In addition, a wall cannot be attached to the top at a time to prevent the tile from being heavy and causing it to fall.
4, wall tiles to be fully immersed
Wall tiles have a high moisture content and must be considered when pasting. The tiling tiles should be soaked in water for at least 10 minutes before they are fully wetted.
Otherwise, the moisture in the mortar is quickly absorbed by the dried tiles and condenses quickly, which affects the fastness of the bond.
Tiles Tiles Cement Lacquer paint Wallpaper Decorative paint Floor tiles Kitchen wall tiles Bathroom wall tiles Bathroom tiles Bathroom tiles Ceramic tile tiles Kitchen tiles
Deck Mount Tub Faucet, Deck Mounted Tub Filler, Deck Waterfall Tub Filler, Deck Tub Faucet with Handshower, Deck Mount Bathtub Faucet
FOSHAN SHAMANDA SANITARY WARE CO., LTD , https://www.shamandahome.com