Ground source and water source heat pump system is mainly composed of underground heat exchange device, heat pump unit and end system. The heat pump unit and the terminal system are quite mature. The underground heat exchange device absorbs energy from the underground through the heat exchange. Due to the ever-changing and complex underground conditions, it is the largest inhomogeneous body in the world. Therefore, the underground heat exchange device How to adapt to local conditions, long-term and stable access to underground heat pump energy required, while not affecting the environment as much as possible, is the installation of water, ground source heat pump system, the key technology. Site Investigation: The site survey mainly includes site investigation, surface water survey and hydrogeological survey. The hydrogeology survey is highly specialized and is the focus of investigation. It must be completed by hydrogeologists. The hydrogeological survey is a survey of the occurrence conditions, movement rules and water chemistry of groundwater in an area. Calculating the amount of resources by collecting relevant parameters, and then putting forward the plan of groundwater supply, which provides the basis for the next system design. Results of Hydrogeological Survey: Hydrogeological Profile Reveals the Results of Hydrogeological Survey of Aquifer Structure: Hydrogeological Map Reveals System Design for Hydrogeological Conditions of Regional Water Richness, Water Level and Flow Direction: The system design is mainly designed for underground heat exchangers. The water source The heat pump system is divided into surface water system and groundwater system. Which system should be adopted is determined by the feasibility analysis of the water supply plan proposed after the site survey. The surface water system collecting device includes two parts: water intake structure and heat exchanger. The water intake structure generally includes a water inlet pipe, a water conduit (or a horizontal water collecting pipe) and a water collecting well, which are greatly influenced by the amount of water, the flow velocity and the water level of the water source. Attention should be paid to the relationship between elevation and changes in the water level during the season. Heat exchanger design is the focus of heat exchanger selection. The length of the heat exchanger depends on the maximum cooling capacity of the water loop in the cooling condition or the maximum heat absorption of the water loop under the heating condition. In the design of the structure and process of the heat exchange coil, the coil should be connected in groups To the loop header, at the same time, arrange the loop header according to the water body and make the loop header the shortest. Groundwater system underground heat transfer devices are mainly water supply wells and recharge wells. The designer arranges well location, well depth and well structure according to local hydrogeological conditions and construction load requirements. In general, both the water supply well and the recharge well should be arranged in areas with good water-richness, at least the water requirements of water source heat pump units should be met. The well depth is determined according to the formation conditions and the demand of water discharge. Take more aquifers; well structure generally includes wellhead, casing, filters, sinking pipe and several other parts, of which the filter is the key to the design. In order to increase the amount of water outflow and to prevent grit blasting, a gravel filter is usually used in loose formations, and the bedrock formation does not leave the filter if the rock is stable. Fill gravel filter is composed of filter tubes and gravel, sometimes wrapped around the filter tube galvanized lead wire or copper wire, nylon mesh. Filtration tube is divided into round and strip type, usually made of steel or cast iron, the porosity of 30% to 50%. Gravel to round, oval is good, prohibited the use of angular crumbs, rock composition should adopt quartzite, limestone, pebbles, can not use the soft rock components such as marl. Gravel size and landfill thickness should be based on the type of aquifer to determine, in the powder, fine, medium, coarse sand gravel, 6-8 times the size of gravel, and try to increase the gravel thickness; gravel Pebble aquifer, particle size 6-10 times the gravel, gravel thickness can be properly reduced. System Installation: The system installation should be strictly in accordance with the design requirements, of which the surface water system installation are basically on the ground operation, easy construction, and groundwater system of water supply wells and recharge wells hidden concealed, you must find a qualified construction Team to complete the specific construction steps, including drilling, logging, down pipe, gravel, well closure, well washing, pumping tests and water quality analysis. Among them, down pipe, gravel, seal well and wash are the key links. Under the pipe according to cuttings cataloging and logging interpretation of the stratigraphy do not under the aquifer strainer, under the aqueduct casing; gravel selected gravel and aquifer particle size to match, and uniform clean Fill the outer side of the drainage pipe; seal wells are filled evenly in the gravel layer of clay to avoid contamination of the aquifer; flushing wells are commonly used carbon dioxide and pressure blower combined washing well, pump pumping well and other methods, according to the actual drilling Of the strata to choose.
Solar Wall Light
â¤[100 LEDs Super Bright Solar Lights Outdoor]The enhanced outdoor solar sports induction lights have 100 LEDs beads,which provide excellent lighting of up to 600 lumens,equipped with a precise Body temperature sensor turn,can immediately illuminate an area and maintain a longer brightness,Strong lighting emission brightens your way home.
☀[270 ° Wide Illumination Angle ]Compared with most similar solar lights on the market, this solar sports induction lights with a motion angle of 270 degrees, , providing Brighter, longer, wider angle illumination.Suitable for outdoor use with balconies, terraces, staircases, gardens, external walls, yard, path, front doors, garages, driveway porches, and lawns, fences, etc
â¤[3 Lighting Modes & PIR motion sensor]There are 3 various modes you can choose. 1.Human body induction mode; 2.Human body interaction + slight light mode; 3.Slight light mode. Please long press the button on the top for 1s to enter another mode.New PIR motion sensor system and the 180owide-angle motion sensor detects motion up to 10-17 ft, it convenience and security to your garage, yard, path.
☀[WATERPROOF IP65 & Easy installation]These solar lights outdoor are IP65 waterproof, are made of high quality ABS, not afraid of outdoor dust and rain. The solar lights can work well even in extreme weather conditions.No annoying wires or adapters needed, the installation is super easy .Just simply find a place with sufficient sunshine and fix the light with supplied screws onto it. the ideal installation height is about 2 to 3 meters, and completed in just a few minutes.
Solar Sensor Wall Light,Solar Powered Led Wall Light,Solar Waterproof Wall Light,Solar Outdoor Wall Lights
Ningbo Wason Lighting Technology Co.,Ltd , https://www.wasonlight.com