1. Be sure to place the plasma display securely in the direction indicated by the packaging arrow to avoid impact.
2. Avoid installing electrical equipment that easily receives electromagnetic waves near the plasma display.
3. Since the plasma display emits infrared light, it may affect other infrared communication devices. Do not place the infrared sensor within the infrared radiation range.
4. Do not leave anything on the plasma display or insert any foreign objects.
5. Do not use when the power cord or power plug is damaged or the plug cannot be securely inserted into the socket.
6. Do not allow the plasma display to come into contact with the rubber nylon product for a long time; do not place the product in a humid, dusty place, under direct sunlight or near any other direct heat source, or expose it to fumes or vapours.
7. Turn off the power before connecting any other device. Please do not hot plug the signal cable.
8. Do not direct the light into the plasma display. Doing so may affect the display.
9. Please avoid liquid contact with the power cord, body and remote control to avoid contact with insecticides or other toxic substances.
10. Do not use voltages other than those specified (220v, 240v ac, 50/60hz).
11. When lightning strikes, do not touch the antenna and the body.
12. Do not display images in 4:3 mode for too long. Do not stay on the same screen for a long time. Otherwise, it may cause screen burns and leave a permanent afterimage on the plasma screen.
13. When the remote control does not work, replace the battery. The batteries must be replaced in pairs and alkaline batteries should be used as much as possible.
14. If any fault occurs to the product, please cut off the power supply (including foreign objects, liquids, product falling down, or damage to the case).
15. Contact the Product Service Center as soon as possible to explain the fault symptoms in detail, and to follow the instructions of the professionals.
16. Do not disassemble the back cover yourself so as not to expose the live parts and high voltage components to danger.
17. When cleaning, please unplug the plug from the socket first.
18. Do not use volatile solvents, thinners, or other chemicals to clean the unit.
19. Please use a dry cotton cloth to remove dust from the plasma display. Even if the body is dirty, do not use detergent directly. So use a soft cloth to dip a neutral cleaning solution that has been diluted with water, and finally use a dry cloth. Wipe clean.
2. Avoid installing electrical equipment that easily receives electromagnetic waves near the plasma display.
3. Since the plasma display emits infrared light, it may affect other infrared communication devices. Do not place the infrared sensor within the infrared radiation range.
4. Do not leave anything on the plasma display or insert any foreign objects.
5. Do not use when the power cord or power plug is damaged or the plug cannot be securely inserted into the socket.
6. Do not allow the plasma display to come into contact with the rubber nylon product for a long time; do not place the product in a humid, dusty place, under direct sunlight or near any other direct heat source, or expose it to fumes or vapours.
7. Turn off the power before connecting any other device. Please do not hot plug the signal cable.
8. Do not direct the light into the plasma display. Doing so may affect the display.
9. Please avoid liquid contact with the power cord, body and remote control to avoid contact with insecticides or other toxic substances.
10. Do not use voltages other than those specified (220v, 240v ac, 50/60hz).
11. When lightning strikes, do not touch the antenna and the body.
12. Do not display images in 4:3 mode for too long. Do not stay on the same screen for a long time. Otherwise, it may cause screen burns and leave a permanent afterimage on the plasma screen.
13. When the remote control does not work, replace the battery. The batteries must be replaced in pairs and alkaline batteries should be used as much as possible.
14. If any fault occurs to the product, please cut off the power supply (including foreign objects, liquids, product falling down, or damage to the case).
15. Contact the Product Service Center as soon as possible to explain the fault symptoms in detail, and to follow the instructions of the professionals.
16. Do not disassemble the back cover yourself so as not to expose the live parts and high voltage components to danger.
17. When cleaning, please unplug the plug from the socket first.
18. Do not use volatile solvents, thinners, or other chemicals to clean the unit.
19. Please use a dry cotton cloth to remove dust from the plasma display. Even if the body is dirty, do not use detergent directly. So use a soft cloth to dip a neutral cleaning solution that has been diluted with water, and finally use a dry cloth. Wipe clean.
The cup brushes remove rust, paint, dust and burrs from surfaces such as metals and wood, and can also be used to level weld spatter. Wire grinder brush for drill can be used for surface adhesion treatment before painting, spray coating and electroplating. It can also be used for surface paint peeling and grinding.Behappy cup brushes are used to remove adhesive residues, hard lime, rust, paint and excess rubber
Cup Brushes,Wire Brus,Steel Wire Brush,Polishing Brush
Behappy Crafts (suzhou)Co.,Ltd , https://www.jshaoyue.com